All plans

10ft x 24in Workbench, 34in High - Garage Miter Saw Station Cut List

This build needs 14 stock boards (34 cuts, 8.3% offcut waste with a 3mm saw kerf). Here is the cut list, the build order and what it costs in timber.

Open this exact build in 3D (free)Get the full PDF - EUR 9.90

Key numbers for this build

Build size3050 x 865 x 610 mm
Primary specBench Footprint: 3050 mm L × 610 mm D
Secondary spec3 Structural Bays × 2 Shelf Levels
Stock boards14 x 2400 mm
Total cuts34 (8.3% waste)
Est. timber costEUR 200 (pro quote ~EUR 1,400)
DRAFTVANO.COM • PREVIEW ONLY • LOCKED CADDRAFTVANO.COM • PREVIEW ONLY • LOCKED CAD3050 mm W x 865 mm H (Watermarked CAD Preview)

Watermarked 2D framing elevation preview. Sheet A-02 in the PDF includes unwatermarked 1:20 / 1:25 dimension arrows and side section.

Cut list preview

PartComponentSectionQtyCut length
L-01Heavy-Duty Laminated Bench Legs38×89mm16x829 mm
F-01Longitudinal Front & Rear Apron Rails38×89mm4xlocked - in PDF
C-01Transverse Cross-Joists (16" O.C. Support)38×89mm10xlocked - in PDF

The first cut length is free. All exact lengths, the board-by-board cutting diagrams and the scaled drawing are in the PDF.

What the PDF blueprint includes

1D Stock Board Cutting Map Preview (2400 mm boards)

Board #1
F-01 (1525mm)
L-01 (829mm)
offcut
Board #2
LOCKED (F-01)
LOCKED (L-01)
Board #3
LOCKED (F-01)
LOCKED (L-01)
Board #4
LOCKED (F-01)
LOCKED (L-01)

Showing first 4 of 14 stock boards (3.0 mm saw-blade kerf compensation active). All 14 boards are mapped in Sheet C-02 of the PDF.

Hardware & Fastener Shopping List

Fastener / MaterialEstimated QtyStructural Use
Structural wood screws 5.0 x 90mm (#10 x 3-1/2")150 pcs (2 boxes of 100)Leg laminating & frame joints
Carriage bolts M10 x 130mm + washers & nuts32 setsLegs to aprons (2 per joint)
Wood screws 4.0 x 40mm (#8 x 1-1/2")62 pcs (1 box of 200)Worktop & shelf from below
PVA / Titebond wood glue1 bottle (500ml)Leg lamination

How to build it

  1. Cut every member from Sheet C-02 board by board, then write its part ID on each piece in pencil so nothing gets mixed up.
  2. Laminate the legs: glue and screw the L-01 pieces together in pairs to make 8 solid posts (8 screws per post, staggered both faces).
  3. Build the top frame and 1 lower shelf frame: front and rear aprons (F-01) with the cross-joists (C-01) between them at ~400mm (16") centres.
  4. Bolt the legs to the frames with carriage bolts, top frame flush with the top of the legs (bench height 865 mm including the top).
  5. Stand the bench on a flat floor, check level both ways and the diagonals for square; shim or trim legs as needed.
  6. Fix the worktop (18-36mm ply/MDF, 3050 mm x 610 mm) from below through the joists so no screw heads show on the work surface.
  7. Fit the lower shelf boards, ease all edges, and seal the top with 2 coats of oil or poly.

Tools: Mitre / circular saw, Drill-driver + impact driver, Spirit level (1200mm / 4ft), Tape measure, square, pencil, Clamps (at least 4), 10mm drill bit + socket set.

FAQ

How much timber do I need?
14 stock boards of 2400 mm (34 cuts in total, 8.3% offcut waste). Estimated timber cost is about EUR 200.
What size is the build?
3050 mm wide x 865 mm high x 610 mm deep. 3 Structural Bays × 2 Shelf Levels.
Can I change the dimensions?
Yes. Open the 3D configurator, move the sliders to your exact room or project size in millimetres or inches, and the cut list, board count and drawings update instantly.
What is in the paid PDF?
A landscape A4 blueprint with every exact cut length, a scaled framing elevation, colour-coded board cutting diagrams, the assembly sequence and a fastener schedule. It is a one-time EUR 9.90 download.

Similar workbench sizes

Other project generators