77" TV Media Wall, 1800mm Fireplace, 2400mm Wall - 3D Stud Blueprint PDF
A printable, to-scale blueprint for this exact 2400 x 2400 x 300 mm build: scaled elevation drawing, colour-coded board cutting diagrams, master cut list and a step-by-step assembly and fixings sheet.
Open this exact build in 3D (free)Get the full PDF - EUR 9.90What the PDF blueprint includes
- Sheet A-01 - project summary and master cut list with every exact length
- Sheet A-02 - to-scale front elevation and side section with dimensions
- Sheet C-02 - colour-coded cutting diagram for every stock board (3mm kerf allowed)
- Sheet D-03 - step-by-step assembly sequence, fastener schedule and tool list
Key numbers for this build
Build size2400 x 2400 x 300 mm
Primary spec77" TV RO: 1770 mm × 1040 mm
Secondary specFire RO: 1810 mm
Stock boards26 x 2400 mm
Total cuts50 (7.2% waste)
Est. timber costEUR 305 (pro quote ~EUR 2,900)
Watermarked 2D framing elevation preview. Sheet A-02 in the PDF includes unwatermarked 1:20 / 1:25 dimension arrows and side section.
Cut list preview
| Part | Component | Section | Qty | Cut length |
|---|---|---|---|---|
| P-01 | Horizontal Sole & Head Plates (Front & Rear) | 38×89mm | 4x | 2130 mm |
| S-01 | Full-Height King Studs (Outer & Center Posts) | 38×89mm | 8x | locked - in PDF |
| T-01 | TV & Fireplace Double-Trimmer Jack Studs | 38×89mm | 4x | locked - in PDF |
| H-01 | TV Recess Top Header & Bottom Sill Plates | 38×89mm | 4x | locked - in PDF |
| B-01 | Heavy-Duty VESA Mount Backer Rails | 38×89mm | 2x | locked - in PDF |
| D-01 | Front-to-Back Depth Spacers & Noggings | 38×89mm | 18x | locked - in PDF |
| F-01 | Fireplace Aperture Lintel & Support Sill | 38×89mm | 4x | locked - in PDF |
| A-01 | Flanking Acoustic Slat Mounting Battens | 38×89mm | 6x | locked - in PDF |
The first cut length is free. All exact lengths, the board-by-board cutting diagrams and the scaled drawing are in the PDF.
1D Stock Board Cutting Map Preview (2400 mm boards)
Showing first 4 of 26 stock boards (3.0 mm saw-blade kerf compensation active). All 26 boards are mapped in Sheet C-02 of the PDF.
Hardware & Fastener Shopping List
| Fastener / Material | Estimated Qty | Structural Use |
|---|---|---|
| Frame fixings 10 x 100mm (or 5 x 100mm screws into joists) | 24 pcs | Sole & head plates to floor / ceiling |
| Structural wood screws 5.0 x 90mm (#10 x 3-1/2") | 221 pcs (3 boxes of 100) | All stud-to-plate & header joints |
| Lag bolts M8 x 100mm (5/16" x 4") + washers | 8 pcs | TV bracket into backer rails |
| Plasterboard screws 3.5 x 38mm | 197 pcs (1 box of 200) | ~6.6 m2 of board skin |
| Plasterboard 12.5mm (1200 x 2400 sheets) | 3 sheets | Front face + returns, incl. 10% waste |
| Brad nails 1.2 x 30mm + grab adhesive | 1 box + 2 tubes | Acoustic slats onto battens |
How to build it
- Mark out: snap chalk lines for the 2130 mm wide x 300 mm deep frame on the floor, transfer them to the ceiling with a laser or plumb bob, and locate the ceiling joists. Check the wall for pipes and cables before fixing.
- Cut every member from Sheet C-02 board by board, then write its part ID on each piece in pencil so nothing gets mixed up.
- Fix the sole plates (P-01) to the floor and the head plates to the ceiling joists, front and rear lines, with a fixing every 400-600mm.
- Stand the full-height king studs (S-01) at both ends of each line; screw through the plates and check plumb in both directions.
- Fit the TV trimmers (T-01), then the TV sill and header (H-01) so the opening measures exactly 1770 mm x 1040 mm, with its bottom edge 1050 mm above the floor.
- Fit the fireplace sill and lintel (F-01) for a 1810 mm x 460 mm opening, bottom 320 mm above the floor. Follow the fireplace maker's clearance and ventilation rules.
- Join the front and rear frames with the depth noggins (D-01) and fit the VESA backer rails (B-01) inside the TV pocket where the bracket bolts will land.
- Run power, HDMI conduit and any LED cabling now, before boarding. Fit the flanking slat battens (A-01) if your design has side wings.
- Board, tape and fill; prime and paint; then hang the TV on the backer rails.
Tools: Mitre / circular saw, Drill-driver + impact driver, Spirit level (1200mm / 4ft), Tape measure, square, pencil, Stud / cable detector, Laser level (recommended).
FAQ
- How much timber do I need?
- 26 stock boards of 2400 mm (50 cuts in total, 7.2% offcut waste). Estimated timber cost is about EUR 305.
- What rough opening do I need for a 77" TV?
- 77" TV RO: 1770 mm × 1040 mm. That includes about 25 mm of clearance on every side for ventilation and mounting.
- What size is the build?
- 2400 mm wide x 2400 mm high x 300 mm deep. Fire RO: 1810 mm.
- Can I change the dimensions?
- Yes. Open the 3D configurator, move the sliders to your exact room or project size in millimetres or inches, and the cut list, board count and drawings update instantly.
- What is in the paid PDF?
- A landscape A4 blueprint with every exact cut length, a scaled framing elevation, colour-coded board cutting diagrams, the assembly sequence and a fastener schedule. It is a one-time EUR 9.90 download.
Similar media wall sizes
- 55" TV Media Wall, 1200mm Fireplace, 2400mm Wall - 3D Stud Blueprint PDF
- 55" TV Media Wall, 1200mm Fireplace, 2400mm Wall - Framing Calculator & Cut List
- 55" TV Media Wall, 1200mm Fireplace, 2400mm Wall - Rough Opening Dimensions
- 55" TV Media Wall, 1500mm Fireplace, 2400mm Wall - 3D Stud Blueprint PDF
- 55" TV Media Wall, 1500mm Fireplace, 2400mm Wall - Framing Calculator & Cut List
- 55" TV Media Wall, 1500mm Fireplace, 2400mm Wall - Rough Opening Dimensions
- 55" TV Media Wall, 1800mm Fireplace, 2400mm Wall - 3D Stud Blueprint PDF
- 55" TV Media Wall, 1800mm Fireplace, 2400mm Wall - Framing Calculator & Cut List