DIY framing plans · Your chosen size
~6ft (1830mm) x ~5ft (1525mm) Sauna Room & Bench Frame
This build needs 41 stock boards (68 cuts, 11.8% offcut waste with a 3mm saw kerf). Here is the cut list, build order and an illustrative materials allowance.
Free 3D preview. Matching custom PDF: EUR 9.90 for one selected configuration. Materials and appliances are not included.
The sample shows a fixed example; your purchased PDF uses the dimensions you select. Check what to measure before you build.
Key numbers for this build
Build size~72in (1830mm) W x ~84.6in (2150mm) H x ~60in (1525mm) D
Primary specRoom volume: 6.0 m³
Secondary spec2 bench tiers • Door clear: ~27.6in (700mm) × ~76.8in (1950mm)
Stock boards41 x ~7.87ft (2400mm)
Total cuts68 (11.8% waste)
Illustrative materials allowanceEUR 1206. Check local prices; excludes appliances and labour.
| Dimension | Imperial / Metric |
|---|---|
| Width | ~6ft (1830mm) |
| Height | ~7.05ft (2150mm) |
| Depth | ~60in (1525mm) |
| Stock board length | ~7.87ft (2400mm) |
| Actual timber section | ~1.5in (38mm) x ~3.5in (89mm) |
Need a custom size?
Framing elevation preview. Sheet A-02 adds dimensions, actual side/plan projections and member positions. Check actual appliance specifications and site measurements before building.
Cut list preview
| Part | Component | Section | Qty | Cut length |
|---|---|---|---|---|
| W-01 | Front & Rear Width Sole/Top Plates | 38×89mm | 4x | ~72in (1830mm) |
| W-02 | Side Wall Sole/Top Depth Plates | 38×89mm | 4x | locked - in PDF |
| S-01 | Front & Rear Full-Height Wall Studs | 38×89mm | 10x | locked - in PDF |
| S-02 | Side Wall Full-Height Studs | 38×89mm | 10x | locked - in PDF |
| K-01 | Full-Height Door King Studs | 38×89mm | 2x | locked - in PDF |
| J-01 | Door Header Jack Studs | 38×89mm | 2x | locked - in PDF |
| R-01 | Door Header Between King Studs | 38×89mm | 1x | locked - in PDF |
| C-02 | Above-Header Infill Blocks | 38×89mm | 3x | locked - in PDF |
| R-02 | Ceiling Depth Ties | 38×89mm | 4x | locked - in PDF |
| B-01 | Bench Front & Rear Long Rails | 38×89mm | 4x | locked - in PDF |
| B-02 | Bench Crossrails | 38×89mm | 8x | locked - in PDF |
| B-03 | Bench Tier 1 Legs | 38×89mm | 8x | locked - in PDF |
| B-04 | Bench Tier 2 Legs | 38×89mm | 8x | locked - in PDF |
The first cut length is free. All exact lengths, the board-by-board cutting diagrams and the scaled drawing are in the PDF.
What the PDF blueprint includes
- Sheet A-01 - project summary and master cut list with every exact length
- Sheet A-02 - scaled front, side and plan projections with member positions
- Sheet C-02 - colour-coded cutting diagram for every stock board (3mm kerf allowed)
- Sheet D-03 - step-by-step assembly sequence, fastener schedule and tool list
The EUR 9.90 purchase covers one selected project and configuration. Sheet M-04 finishing and utility planning notes are optional at EUR 4.90 extra. Long tables may continue onto additional pages.
1D Stock Board Cutting Map Preview (2400 mm boards)
Showing first 4 of 41 stock boards (3.0 mm saw-blade kerf compensation active). All 41 boards are mapped in Sheet C-02 of the PDF.
Hardware & fastener shopping list
| Fastener / material | Estimated quantity | Use |
|---|---|---|
| Stainless / galvanised screws 5.0 x 90mm | 300 pcs (3 boxes of 100) | Frame joints (heat & moisture) |
| Stainless T&G cladding nails 40mm | 603 pcs (2 boxes of 500) | ~17.2 m2 of cedar |
| Aluminium foil tape 50mm | 2 rolls | Vapour barrier seams |
| Stainless screws 4.5 x 50mm | 120 pcs | Bench slats, fixed from below |
Assembly guidance for this frame
- Prepare the site and confirm the complete room build-up for the location. Select the actual heater with its manufacturer or a qualified installer, then have an electrician confirm the required power supply before building.
- Cut every member from Sheet C-02 board by board, then write its part ID on each piece in pencil so nothing gets mixed up.
- Build all four wall perimeters: W-01 full-width front/rear sole/top plates, plus W-02 side plates BETWEEN their inner faces. The two lengths and all eight plate runs are listed separately.
- Fit S-01 front/rear studs and S-02 rotated side-wall studs at the member-placement coordinates. Keep the centred door zone clear; fit the full-height K-01 kings and shorter J-01 jacks as separately scheduled.
- Rest the single on-edge R-01 header on the J-01 jacks between the kings. It leaves 700 mm x 1950 mm clear above the sole plate. Fit any listed C-02 upper infill blocks and the R-02 flat ceiling ties. Check the actual door/frame and roof/ceiling design separately.
- Build each bench frame with B-01 long rails and B-02 crossrails at its listed supports. Use the tier-specific leg IDs in the schedule. Retained deck heights: 450 mm, 900 mm; 44mm separate decking allowance is included in each leg calculation.
- Bench platforms stagger by 450mm in depth, highest at the rear. Check usable access, headroom, joints, loading and the actual heater clearances before building; more than two tiers remains unavailable for a new checkout pending separate review.
- Specify the complete insulation, vapour control, battens, lining, roof, bench decking, ventilation and appliance installation with a qualified installer. These separate materials and installation details are not supplied by the timber cut schedule.
Tools: Mitre / circular saw, Drill-driver + impact driver, Spirit level (1200mm / 4ft), Tape measure, square, pencil, Staple gun, Brad nailer (stainless nails).
FAQ
- How much timber do I need?
- 41 stock boards of ~7.87ft (2400mm) (68 cuts in total, 11.8% offcut waste). Illustrative materials allowance: EUR 1206. Confirm local prices; appliances and labour are excluded.
- What size heater does this sauna need?
- Room volume: 6.0 m³. Always confirm with your heater maker's room-size table and have an electrician check the supply.
- What size is the build?
- ~72in (1830mm) wide x ~84.6in (2150mm) high x ~60in (1525mm) deep. 2 bench tiers • Door clear: ~27.6in (700mm) × ~76.8in (1950mm).
- Can I change the dimensions?
- Yes. Open the free 3D preview and enter your width, height and depth in millimetres or decimal inches. The frame, cut list and board count update to your selected dimensions.
- What is in the paid PDF?
- A landscape A4 blueprint with every exact cut length, a scaled framing elevation, colour-coded board cutting diagrams, the assembly sequence and a fastener schedule. It is a one-time EUR 9.90 download.
Similar sauna sizes
- ~6ft (1830mm) x ~4ft (1220mm) Sauna Room & Bench Frame
- ~6ft (1830mm) x ~6ft (1830mm) Sauna Room & Bench Frame
- ~6ft (1830mm) x ~7ft (2135mm) Sauna Room & Bench Frame
- ~6ft (1830mm) x ~8.01ft (2440mm) Sauna Room & Bench Frame
- ~5ft (1525mm) x ~4ft (1220mm) Sauna Room & Bench Frame
- ~5ft (1525mm) x ~5ft (1525mm) Sauna Room & Bench Frame
- ~5ft (1525mm) x ~6ft (1830mm) Sauna Room & Bench Frame
- ~5ft (1525mm) x ~7ft (2135mm) Sauna Room & Bench Frame