DIY framing plans · Your chosen size
~8.01ft (2440mm) Workbench Frame, 610mm Deep, 1015mm High
This build needs 11 stock boards (30 cuts, 6.8% offcut waste with a 3mm saw kerf). Here is the cut list, build order and an illustrative materials allowance.
Free 3D preview. Matching custom PDF: EUR 9.90 for one selected configuration. Materials and appliances are not included.
The sample shows a fixed example; your purchased PDF uses the dimensions you select. Check what to measure before you build.
Key numbers for this build
| Dimension | Imperial / Metric |
|---|---|
| Width | ~8.01ft (2440mm) |
| Height | ~3.33ft (1015mm) |
| Depth | ~24in (610mm) |
| Stock board length | ~9.84ft (3000mm) |
| Actual timber section | ~1.5in (38mm) x ~3.5in (89mm) |
Need a custom size?
Framing elevation preview. Sheet A-02 adds dimensions, actual side/plan projections and member positions. Check actual appliance specifications and site measurements before building.
Cut list preview
| Part | Component | Section | Qty | Cut length |
|---|---|---|---|---|
| L-01 | Paired laminated leg members | 38×89mm | 16x | ~38.5in (979mm) |
| F-01 | Front & rear apron rails | 38×89mm | 4x | locked - in PDF |
| C-01 | Cross-joists between apron faces | 38×89mm | 10x | locked - in PDF |
The first cut length is free. All exact lengths, the board-by-board cutting diagrams and the scaled drawing are in the PDF.
What the PDF blueprint includes
- Sheet A-01 - project summary and master cut list with every exact length
- Sheet A-02 - scaled front, side and plan projections with member positions
- Sheet C-02 - colour-coded cutting diagram for every stock board (3mm kerf allowed)
- Sheet D-03 - step-by-step assembly sequence, fastener schedule and tool list
The EUR 9.90 purchase covers one selected project and configuration. Sheet M-04 finishing and utility planning notes are optional at EUR 4.90 extra. Long tables may continue onto additional pages.
1D Stock Board Cutting Map Preview (3000 mm boards)
Showing first 4 of 11 stock boards (3.0 mm saw-blade kerf compensation active). All 11 boards are mapped in Sheet C-02 of the PDF.
Hardware & fastener shopping list
| Fastener / material | Estimated quantity | Use |
|---|---|---|
| Structural wood screws 5.0 x 90mm (#10 x 3-1/2") | 132 pcs (2 boxes of 100) | Leg laminating & frame joints |
| Carriage bolts M10 x 130mm + washers & nuts | 32 sets | Legs to aprons (2 per joint) |
| Wood screws 4.0 x 40mm (#8 x 1-1/2") | 56 pcs (1 box of 200) | Worktop & shelf from below |
| PVA / Titebond wood glue | 1 bottle (500ml) | Leg lamination |
Assembly guidance for this frame
- Cut every member from Sheet C-02 board by board, then write its part ID on each piece in pencil so nothing gets mixed up.
- Laminate the legs: glue and screw the L-01 pieces together in pairs to make 8 solid posts (8 screws per post, staggered both faces).
- Build the top frame and 1 lower shelf frame using the F-01 aprons and 10 C-01 cross-joists in the cut list. Place the cross-joists in the gaps between leg positions as shown in the plan projection and member coordinates; the front apron conceals their ends in the front elevation. Confirm joints and supports suit the actual worktop and intended loads.
- Place each paired leg BETWEEN the front and rear apron faces; do not put a leg and apron in the same timber volume or cut an unspecified notch. Bolt the legs to the frames with suitable reviewed connections, top frame flush with the top of the legs (bench height 1015 mm including the top).
- Stand the bench on a flat floor, check level both ways and the diagonals for square; shim or trim legs as needed.
- Plan the worktop at 2440 mm x 610 mm separately. The listed leg lengths allow a 36mm top; a different top thickness needs its leg allowance reviewed before cutting. Confirm the worktop material and its fixings suit your intended use.
- Fit the lower shelf boards, ease all edges, and seal the top with 2 coats of oil or poly.
Tools: Mitre / circular saw, Drill-driver + impact driver, Spirit level (1200mm / 4ft), Tape measure, square, pencil, Clamps (at least 4), 10mm drill bit + socket set.
FAQ
- How much timber do I need?
- 11 stock boards of ~9.84ft (3000mm) (30 cuts in total, 6.8% offcut waste). Illustrative materials allowance: EUR 181. Confirm local prices; appliances and labour are excluded.
- What size is the build?
- ~96.1in (2440mm) wide x ~40in (1015mm) high x ~24in (610mm) deep. 3 Structural Bays × 2 Shelf Levels.
- Can I change the dimensions?
- Yes. Open the free 3D preview and enter your width, height and depth in millimetres or decimal inches. The frame, cut list and board count update to your selected dimensions.
- What is in the paid PDF?
- A landscape A4 blueprint with every exact cut length, a scaled framing elevation, colour-coded board cutting diagrams, the assembly sequence and a fastener schedule. It is a one-time EUR 9.90 download.
Similar workbench sizes
- ~8.01ft (2440mm) Workbench Frame, 1220mm Deep, 1015mm High
- ~8.01ft (2440mm) Workbench Frame, 760mm Deep, 1015mm High
- ~8.01ft (2440mm) Workbench Frame, 915mm Deep, 1015mm High
- ~8.01ft (2440mm) Workbench Frame, 1220mm Deep, 865mm High
- ~8.01ft (2440mm) Workbench Frame, 610mm Deep, 865mm High
- ~8.01ft (2440mm) Workbench Frame, 760mm Deep, 865mm High
- ~8.01ft (2440mm) Workbench Frame, 915mm Deep, 865mm High
- ~8.01ft (2440mm) Workbench Frame, 1220mm Deep, 915mm High